Beacon Morris Garage Heater Installation Manual
Hello I just purchased a Beacon Morris garage heater. Beacon/Morris Residential. Your wiring diagram and furnace service manual is on the right side.
Visit our website at This video shows the vertical venting installation for the Beacon Morris BRT045 heater in separated combustion mode. Quicktech For Windows Iso Creator. I bought the concentric vent kit from littlegreenhouse.com.
The gaskets included in their kit make the installation cleaner. Other sellers may not provide the gaskets. Also, as mentioned in the video, it might make more sense to buy the UL 1738 special gas pipe in separate pieces for a vertical installation.
Adjustable lengths of pipe are also available. Your local municipality may allow b-vent to be used, which is a much cheaper option. Pricing info for major expenses as of 12/7/15: - Beacon Morris BRT045 heater: $499 + about $50 shipping @ Menard's.
Menard's may no longer ship this heater. Also available here: - Concentric vent kit (AS-X7-4): $217 @ littlegreenhouse.com (free shipping and orange gaskets included) - 4' special gas pipe: FSVL2404 (24' pipe): FSVL3604 (36' pipe): FSAAU4 (Adapter): FST4 (Tee): FSTC4 (Tee cap): FSAVL4 (Adjustable pipe): - Malco C5R crimpers: - Vent roof flashing and storm collar: $30 - Gas line installation: $20/linear foot x 30 ft = $600 (after watching and assisting the plumber, would probably do myself if I had to do it again and if DIY is allowed in my area) - Electrical wiring and conduit: Approx $125 for tools and materials. Conduit bender: - Thermostat (Lux TX9600TS - touch screen and programmable): $30 used on Amazon - Mechanical and electrical permits: Approx $125 ========================= Approx. Misc: $2000 Video 1 of 3: Video 3 of 3: DISCLAIMER: This video and description contain affiliate links, which means that if you click on one of the product links and make a purchase, I’ll receive a small commission.
This helps support the channel and allows us to continue to make videos like this one. Thanks for the support!
Problem: Your furnace will not ignite the gas to produce heat for your home. When a furnace has a bad ignitor what I see most of the time is the following sequence of operation: 1. Thermostat calls for heat. Draft inducer motor starts. Pressure switch attached by a small plastic or rubber tube senses the negative pressure produced by the draft inducer and closes.
Draft inducer runs for 30 seconds to a minute before you hear a gas hissing sound. The ignitor did not glow, the flame sensor (a small metal probe about 1/8' in diameter, with a white porcelain base) does not sense the flame, so after 8 to 10 seconds the hissing sounds stops with no ignition of gas to heat your home. Your furnace shuts down and goes into a lock out condition until you turn your power switch back off and on again.
Then the sequence starts all over again with no ignition of the gas. Solution: You probably need to purchase and install a new ignitor. I would suggest that you inspect your ignitor closely for cracks. Make sure you do not touch the ignitor with your bare hands.
If you do not visually see a crack, then you could have a furnace control board problem or a limit, rollout switch problem. I have the same problem with a 5 or 6 year old Beacon Morris Brut. I had it installed in a garage but never use it. Today I decided to turn it on and it wouldn't light. I talked to the installer and he suggested bleeding out the natural gas so I did that right up to and inside the unit. It managed to light once after I set the thermostat to 90 and had the little allen bleeder screws loose. It hasn't worked again though.
The fan comes on to evacuate the heater and the electric igniters come on but no gas is coming through the control valve. This heater has had zero use.
Maestro Peter Goldsworthy Ebook more. The igniters attempt to light three times and then the unit shuts off and it won't try again until it has set with the power to it turned off for a bit. Very frustrating. Is this some sort of chronic problem for this heater? Now my Beacon Morris garage heater won't stay lit. It fires and lights, stays lit for a few seconds then shuts off.
Starts again, fires, stays lit for a few seconds and then shuts off. Over and over. Talked to a tech at Beacon Morris, he gave me a few things to check and then determined I had a bad control board. Couldn't order it direct from him so went to Menards and place a special order that took 3 weeks to come in. Installed it today and same exact issue!!!
Start, burn, shut off, over and over. Any help would be appreciated.